|
Recommended accessories
This pump is the world's first pump to be used in serial-production water-cooled workstations and is ideally suited for watercooling of processors and other electronic components. Thanks to its compact design and performance it can also be used for a multitude of other applications. This pump is an electronically commutated ball motor pump which offers running times of significantly more than 50.000hrs at 12 volts. The only moving part in a ball motor pump is the spherically shaped rotor unit which is resting on an ultra-hard, war-free ceramic bearing ball. A conventional shaft with bearings and gaskets is not needed! The spherical bearing of the rotir unit on a ceramic bearing ball offers a multitude of advantages: The development of bearing play is not possible with this design, hence keeping noise emissions to a minimum over the whole lifespan of the unit. The bearing is also self-adjusting and lubricated directly by the transported medium (wet rotor design). Maintenance of the pump hence becomes obsolete. As the rotor is held in place magnetically even smaller particles pose no problem for the operation of the pump. Blocking of the pump is virtually impossible under normal circumstances. Even after a longer period of non-operation a safe start of the unit is ensured. The permanently magnetic rotor unit is driven by a magnetic field which is produced by the surrounding stator. This stator is completely built around the rotor. Hence the whole pump with its 38mm of height is only slightly taller than the stator itself. It hence fits easily into all common PC-, Barebone- and Mini-PC cases. A separate magnetic shielding is usually not required. The ball motor principle allows energy-saving operation with comparatively high performance. By voltage variation the DC -operated pump can easily be adjusted in power. All materials in contact with the medium are completely corrosion-resistant. Alphacool Laing DDC Plexi top HF 38 Version G3/8: The proven design of the Alphacool Laing top meets the future: Extreme highflow with 3/8” connection threads
This top replaces the black standard cover of the Laing DDC-1T and Laing DDC-1Plus pumps and adds many additional and very useful features. One of the most important is the use of 3/8” threads which makes you independent of the barbs on the original cover. The use of 3/8” threads, which have a much larger inner diameter than the common 1/4” threads on Laing covers, also makes this cover the ultimate choice for highflow applications. Rebuilding of the pump to use this cover is easy: Simply remove the 4 screws at the bottom of the pump and lift off the original cover. Then insert the 4 included screws instead of the original ones and put the cover on top of the pump. Simply tighten the screws and you are set to go! To ensure a safe seal of the cover simply leave the original O-ring gasket in its place during installation. Optionally this cover also offers the possibility for decoupled installation of the pump in a 3,5” drive bay. For use of this feature only one of our decoupling kits (Prod..No.: 13701) is required to allow quick, compact and decoupled installation of the pump. This cover is also the basis for installation of a reservoir on this pump. The optional reservoir, available at the product number 13905, can simply be screwed onto the cover and the coling loop comes to life! Technical specifications: Dimensions pump: (WxDxH) 62x62x38mm (without fittings) Dimensions Plexi top: 80x80x20mm (without fittings) Motor design: Electronically commuted ball motor Nominal voltage: 12 V DC Rated voltage range: 6 to 13,2 Volts Pressure head at 12V: 4.7m max. flow rate: 600l/h Rated coolant: Water, water-/glycol mixtures* Max. system temperature: 60° C Materials in contact with medium: Stainless steel 1.4571, PPS-GF40, EPDM O-rings, Aluminium oxide, hard coal Extent of delivery: Note regarding mounting: After mounting a small gap remains between pump and top. The fit is tight as the O-ring ensures a safe seal. Hence do not over-tighten the screws, as it may result in damages to the top. Pump rpm signal: The 3-Pin Molex plug can be used for monitoring of the pump's speed (For Mainboards or controllers) Note: This pump is of the newest revision. IMPORTANT: We recommend the use of lubricating water additives such as AT Protect Plus or Innovatek Protect. Anti-Corro-Fluid is not recommended! Please note: Due to the performance of this pump it may only be used in a loop with at least one waterblock. When used without load the pump may be damaged! Please note: The electronics on this Laing pump is not water-resistant. Please always make sure to avoid any contact of the pump with water. When replacing the top makes sure that the gasket is correctly in position and if you are filling a Laing reservoir top make sure that no coolant is spilled. Damages by water/coolant are not covered by the warranty and will not be replaced by Laing! Why is there a Laing and a Swiftech version? What are the differences? This product has been reviewed for you: |
|
